Chromaticity-tunable remote LuYAG: Ce phosphor-in-glass film on regular textured glass substrate for white light emitting diodes

All inorganic remote phosphor-in-glass film exhibits excellent properties in high power white light-emitting-diodes (WLEDs) thanks to their easy fabrication and thermal stability. Herein, fabrication of (Lu, Y)₃Al₅O₁₂: Ce³⁺ (LuYAG: Ce)phosphors embedded in borosilicate glass film by the conventional solid state reaction and spin coating technology has been reported. The introduction of Y³⁺ ions reduces the difference of relative growth rate along some directions in growth of LuYAG microparticles, yielding a finer grain with smooth edges. By adjusting the molar concentration of Y³⁺ ions in LuAG phosphor, a series of tunable broadband emission from green to yellow region is observed and maintains excellent thermal stability. Meanwhile, the decay curves of samples with different Y³⁺ are almost same. SEM images show that phosphor particles are homogenously distributed within the glass matrix and keep their original morphology, suggesting the phosphor-in-glass films were synthesized as expected. Finally, a simple WLEDs based on the films was constructed using the commercial blue chip. The correlated color temperature ranging from 4853K to 4627K and high color rendering index from 81.4–79.7 were obtained. Upon the different driving current, the chromaticity coordinates of as-fabricated film exhibit good light color stability. These results bring an inspiring insight to tune the luminescent performance for remote WLEDs.     

Warpage control method during surface forming process of plastic film-reinforced flexible decorative veneer

The plastic film of the new plastic film reinforced pliable decorative veneer (PRPDSV) is used as a flexible reinforcement material and an adhesive material. It has good water resistance, impermeability, simple preparation and finishing processes, and no formaldehyde release. However, warpage phenomenon during hot pressing has been a bottleneck problem restricting its industrial development. In order to solve this problem solve, the study proposed a concave, and convex molds method, established an elastic–plastic FEA model of hot pressing processes of the PRPDSV using concave and convex molds with static/general static solution module in the nonlinear ABAQUS, and researched the effect on the performances of the PRPDSV from the parameters of temperature, pressure, and mold curvature radius theoretically and verified experimentally. Analysis results showed that the surface forming temperature had a great effect on warpage control for PRPDSV. The higher the temperature is, the smaller the curvature radius of the corresponding mold will be and the better the warpage will be. The curvature radius of the molds had a significant effect on the warpage control. Under the conditions with the same hot pressing parameters, the smaller the curvature radius is, and the better control on the warpage for the PRPDSV will be.     

Effects of structural parameters on water film properties of transpiring wall reactor

Corrosion and salt deposition problems severely restrict the industrialization of supercritical water oxidation. Transpiring wall reactor can effectively weaken these two problems by a protective water film. In this work, methanol was selected as organic matter, and the influences of vital structural parameters on water film properties and organic matter removal were studied via numerical simulation. The results indicate that higher than 99% of methanol conversion could be obtained and hardly affected by transpiration water layer, transpiring wall porosity and inner diameter. Increasing layer and porosity reduced reactor center temperature, but inner diameter's influence was lower relatively. Water film temperature reduced but coverage rate raised as layer, porosity, and inner diameter increased. Notably, the whole reactor was in supercritical state and coverage rate was only approximately 85% in the case of one layer. Increasing reactor length affected slightly the volume of the upper supercritical zone but enlarged the subcritical zone.     

Influence of substrate temperature on the microstructure of YSZ films and their application as the insulating layer of thin film sensors for harsh temperature environments

Thin film sensors are employed to monitor the health of hot-section components of aeroengine intelligence (for instance, blades), and electrical insulating layers are needed between the metal components and thin film sensors. For this purpose, the electrical insulation characteristics of an yttria-stabilized zirconia (YSZ)/Al₂O₃ multilayer insulating structure were investigated. First, YSZ thin films were deposited by DC reactive sputtering at various substrate temperatures, and the microstructural features were investigated by scanning electron microscopy and X-ray diffraction. The results indicate that the micromorphology of the YSZ thin film gradually became denser with increasing substrate temperature, and no new phases appeared. The compact and uniform topography of the YSZ thin film improved the insulation properties of the multilayer insulating structure and enhanced the adhesion of the thin film sensors. In addition, the electrical insulation properties of the YSZ/Al₂O₃ multilayer insulating structure were evaluated via insulation resistance tests from 25 to 800 °C, in which the YSZ thin film was deposited at 550 °C. The results show that the insulation resistance of the multilayer structure increased by an order of magnitude compared with that of the conventional Al₂O₃ insulating layer, reaching 135 kΩ (5.1 × 10^?6 S/m) at 800 °C. Notably, the insulation resistance was still greater than 75 kΩ after annealing at 800 °C for 5 h. Finally, the shunt effect of the YSZ/Al₂O₃ multilayer insulating structure was estimated using a PdCr thin film strain gauge. The relative resistance error was 0.24%, which demonstrates that the YSZ/Al₂O₃ multilayer insulating structure is suitable for thin film sensors.     

High-temperature electrical properties of polymer-derived ceramic SiBCN thin films fabricated by direct writing

The in situ temperature monitoring of hot components in harsh environments remains a challenging task. In this study, SiBCN thin-film resistance grids with thicknesses of 1.8 μm were fabricated on alumina substrates via direct writing. Owing to their dense microscopic morphology and extremely high graphitisation level, the produced SiBCN films exhibited large high-temperature oxidation resistance and electrical conductivity. The resistance–temperature, stability, and repeatability characteristics of these films were examined in an aerobic environment at temperatures up to 800 °C. The obtained results revealed that the thermistor resistance decreased monotonously with increasing temperature from room temperature to 800 °C. The SiBCN film resistance variations observed during repeated temperature cycling in the regions of 505–620 °C and 610–720 °C were 0.09% and 1.7%, respectively. The high cyclability and stability of the SiBCN thin film thermistor suggested its potential applicability for the in situ temperature monitoring of hot components in harsh environments.     

基于多特征融合的电影推荐系统

协同过滤算法（CF）根据用户-物品的评分矩阵做推荐，未考虑物品自身属性。本文将MovieLens数据集上的电影属性，作为影响推荐结果的因素，融合电影的简介、评论、评分、导演和演员等多种因素，进行推荐。使用CNN（卷积神经网络）和Word2Vec（Word to Vector,词向量模型）处理电影简介；使用AFINN（Finn rup Nielsen情感词典）处理评论，并对结果进行映射；对导演和演员数据进行建模，得到该因素下的预测评分，最后将各因素下的结果进行加权融合，通过调整权重，得到最佳效果。经验证，该方法的推荐性能优于传统的CF算法。     

Digital image correlation for strain measurement in plastic film blowing process

Surface deformation study of a polymer film during plastic film blowing (PFB) extrusion process though is considered essential, is difficult to execute as the process is fast and continuous. Digital image correlation (DIC) is an optical technique that is non-destructive, highly accurate and designed to measure deformations from micro to macro scale. DIC can be proposed as a reliable tool to understand the relationship of polymer structure-processing-properties. In this literature, digital image correlation, its basic principle of operation and reliability guided DIC for continuous large deformation are comprehensively explored. Versatility of DIC, and the conditions that affect the measurement algorithm as well as preceding use of DIC in polymer processes are reviewed. The implementation and potential use of DIC in PFB are described.

This review was submitted as part of the 2019 Materials Literature Review Prize of the Institute of Materials, Minerals and Mining run by the Editorial Board of MST. Sponsorship of the prize by TWI Ltd is gratefully acknowledged.     

羧基含氟聚合物纳米纤维膜的制备及对铜(II)的吸附性能

以甲基丙烯酸十二氟庚酯(DFHMA)和甲基丙烯酸(MAA)为单体,通过溶液聚合法制备出共聚物DFHMA-co-MAA,将DFHMA-co-MAA与聚偏氟乙烯(PVDF)按一定质量共混,采用静电纺丝方法,制备出羧基含氟聚合物(PVDF-DM)纳米纤维膜,用以吸附溶液中Cu(II)。讨论了PVDF和DFHMA-co-MAA的质量配比对纤维微观形貌和对Cu(II)吸附性能的影响,得出当PVDF与DFHMA-co-MAA的质量比为1∶2时,纤维的微观直径较均一且吸附性能最佳,故实验采用该质量配比制备PVDF-DM。使用红外光谱对PVDF-DM进行表征,显示出PVDF-DM纤维膜中含有—OH和C＝O等活性吸附基团。以PVDF-DM纳米纤维膜为吸附剂,探讨了吸附剂用量、吸附pH值和吸附时间对Cu(II)吸附性能的影响,并研究了吸附过程的动力学模型。结果表明,室温下,当吸附剂用量为0.03g,pH=5时,吸附60min达到吸附平衡,吸附率和吸附量分别为94.37%和62.91mg/g,PVDF-DM纳米纤维膜对Cu(II)的吸附过程同时满足拟一级动力学和拟二级动力学模型,说明该吸附过程包含了化学吸附和物理吸附。PVDF-DM纳米纤维膜循环使用5次后,吸附能力仅降低16.23%,说明PVDF-DM纳米纤维膜具有很好的再生使用能力。     

Multi-field coupling thermo-acoustic radiation using free-standing nano-thin films in a static magnetic field

Abstract

Thermo-acoustic radiation from nano-thin film has been widely reported these years. In this paper, a static magnetic field is introduced to enhance the acoustic power in the multi-field thermo-acoustic generation. The coupled thermo-acoustic system in a static magnetic field shares the same acoustical unit with very few additional components. In the presence of a static magnetic field, thin-film vibration is excited instead of being still in the classical thermo-acoustic system. Not surprisingly, a steady magnetic field has very little impact on the thermo-acoustic generation system when a constant amplitude sinusoidal current is introduced. The oscillation perpendicular to the nano-thin film is driven by the electromagnetic force. The system response of thermo-acoustics and magneto-acoustics can be generally matched when suitable parameters are introduced. The acoustical pressure output can be significantly improved in the presence of a static magnetic field although more electrical input power should be provided in the multi-field thermo-acoustic system. Evidently, the coupled multi-field acoustical system is able to handle more electrical power input and the power input can be more easily dissipated relatively. The results show that the acoustic response of this new multi-filed coupled system can be significantly improved as compared to the classical system without magnetic effects.